Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
This post which follows about Installing A Bathtub is exceedingly interesting. You should take a look.
Setting up a bathtub isn't specifically rocket science, but it does require strong plumbing, woodworking, and also in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard task. If the old tub is easily accessible, the project can relocate immediately; if you need to open a wall to get rid of the old bathtub and position the new bath tub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will certainly require a helper to vacate the old tub and set in the brand-new one. See to it you have qualified yourself for the job and also fit trying it. Instead of employing a service provider to take over a halfway-completed project, it is much better to consider using one prior to you start. Chances are you may require a professional plumber to make tube links.
This post will certainly help you set up a brand-new tub in your washroom if you have actually currently gotten a brand-new bathtub as well as don't require to transform the arrangement of your previous water pipelines.
Your devices and also product list must make up the following:
Getting ready for the Setup
Firstly, the sustaining frame provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps system to avoid strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its last setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the restricted access that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will originate from the pipes. As soon as the supply pipelines have been removed, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming throughout this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before proceeding to fit the new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The following objective is to make certain that the tub is leveled all round. This can be attained by examining the level and readjusting the feet on the tub up until the level checks out degree.
To install faucets, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipe by making a compression join; after that do the very same for the other faucet.
Turn on the water and also inspect all joints and also new pipework for leaks and tighten them if required. Fill the tub and additionally examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bathtub needs to wait up until the bathtub has actually been made use of a minimum of once as this will resolve it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washers are in place between the faucet as well as the sink. Safeguard the tap in position with the manufacturer provided backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap ports. The former type ought to be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break a stiff seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components and also installations. They are sold in tubes and cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to always load the tub with water before securing, to permit the movement experienced when the bathtub remains in usage. The sealer can fracture rather early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the marketplace. It is recommended to fit the tiles using waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Hopefully you enjoyed reading our excerpt about Installing A Bathtub. Thanks a lot for taking time to read our blog. Do you know about another individual who is in the market for the niche? Take a moment to promote it. We take joy in reading our article about How to Install a Bathtub.
Excellence awaits, dial! Report this page